Monogram ZBD1850 Especificações

GE AppliancesGeneral Electric CompanyLouisville, Kentucky 4022531-917518-in. Dishwasherwith Top ControlsPDW1800PDW1860ZBD1850ZBD1870Technical Service

– 10 –Component Locator ViewsControl Panel View Access Panel Fill FunnelDrain PumpPressure Switch HoseFill HoseDoor Tension SpringRight Side View (Ins

– 11 –Interior View (With Bottom Rack Removed for Clarity)Detergent/Rinse Module Compartment ViewStatic Dry VentDetergentCompartmentCompartment LidSi

– 12 –Interior View of Basin (With Racks Removed)Bottom View (Looking Up)Heating ElementSpray ArmFilter AssemblyMicro-fi lterClamp NutSump ScreenSumpDr

– 13 –Dishwasher ComponentsThroughout this manual, features and appearance may vary from your model.Door PanelThe door panel covers the door to the di

– 14 –Door Latch AssemblyThe door latch assembly is located on the door assembly behind the control panel cover. The dishwasher will not operate until

– 15 –5. Inspect the o-ring. If the o-ring shows obvious signs of wear or damage, replace the duct vent and gasket assembly.Static Dry SystemThe stat

– 16 –When activated for the second time in a cycle, the lever lifts the connecting rod by the notch, lifting the rinse dispenser plunger (4) and rele

– 17 –Door AssemblyRemoval and Replacement1. Disconnect power.2. Carefully pull the dishwasher out from its installation.3. Remove the control pane

– 18 –15. Close the dishwasher door.Caution: The star washer is easily damaged during removal and should not be reused. Order a new set of star wash

– 19 –3. Reverse the above procedure to install.Note: When installing the tub seal, make sure it is seated properly in the seal channel. Run your fi

– 2 –IMPORTANT SAFETY NOTICE The information in this service guide is intended for use byindividuals possessing adequate backgrounds of electrical,el

– 20 –6. Disconnect the 2 terminal lugs from the heating element.Heating ElementThe heating element maintains water temperature during the wash and r

– 21 –Fill FunnelThe fi ll funnel is mounted on the right side of the tub. Its purpose is to provide a method of supplying water for the wash and rinse

– 22 –3. Disconnect the incoming water line from the water fi ll valve port.4. Remove the 2 screws and mounting bracket from the dishwasher.5. Remov

– 23 –Removal and Replacement1. Disconnect power.2. Carefully pull the dishwasher out from its installation.3. Remove the 4 Phillips-head screws, a

– 24 –5. Label and disconnect the two wires from the drain pump.PortDrain Pump AssemblyThe drain pump assembly is located under the tub at the right,

– 25 –4. Label and disconnect the 2 terminals to the motor wire connector.ConnectorMotor Pump AssemblyThe motor pump assembly is located under the tu

– 26 –Note: Do not attempt to remove the Phillips-head screw and locknut that connect the motor mount to the dishwasher frame.8. Disconnect the groun

– 27 –Sump AssemblyThe sump assembly consists of the fi lter assembly, micro-fi lter, sump clamping nut, sump gasket, and sump. The fi lter assembly prev

– 28 –(Continued next page)Note: The sump clamping nut turns counterclockwise and may be diffi cult to remove. It may be necessary to insert a screwd

– 29 –Using a small fl at-blade screwdriver, lift each of 6. the 2 lock tabs (one on each side) that hold the thermistor to the sump.Slide the thermist

– 3 –TABLE OF CONTENTSBottom Door Seal...

– 30 –TroubleshootingWARNING: Always turn off the electric power supply before servicing any electrical component, making ohmmeter checks, or replacin

– 31 –Troubleshooting the Water ValveIf the water valve is suspected of faulty operation, refer to the strip circuit and proceed as follows:1. Disc

– 32 –Troubleshooting the Wash Pump MotorThe wash pump motor does not start immediately when the dishwasher cycle has started. The tub will begin fi ll

– 33 –Service Mode

– 34 –Troubleshooting ChecklistThe troubleshooting checklist is common for all dishwasher models. They use different parts to accomplish the same thin

– 35 –Symptom Check for the Following RemedyNo heat during the dry cycle.1. Defective heater element. 1. Replace the heater element.2. Damaged or def

– 36 –Sympton Check for the Following RemedyPoor washability. 1. Improper loading of dishes, pots, pans, and nesting of silverware.1. Instruct the cu

– 37 –Symptom Check for the Following RemedyNoisy pump assembly. 1. Debris in bottom of tub sump area.1. Clean out the sump area.2. Pump parts were no

– 38 –Washability ComplaintsHot Water – Ample supply of water at a temperature of 120°F (60°C) is necessary for best results. Do not use dishwasher so

– 39 –SchematicWARNING: Power must be disconnected before servicing the appliance.Note: Schematic diagram subject to change. Please refer to diagram s

– 4 –IntroductionThe 18-in. Built-In Dishwasher with top controls has a compact size, allowing the unit to fi t in areas as small as 18 inches (45.72 c

– 40 –WarrantyFor The Period Of: GE Will Replace:One Year Any part of the dishwasher which fails due to a defect in materials or workmanship. DuringFr

– 5 –Model DesignatorCompact 18-in. NomenclatureZ B D 1 8 0 0 M S SBrandZ = Monogram P = Profi leProduct Type

– 6 –Custom Panel InstallationSome models of this dishwasher are designed for use with a 3/4-in. custom front panel. For easier installation, the cust

– 7 –facing up. If the back surface of the panel is not fl at, use the spacer pads provided. Drive the 1/2-in. Phillips fl at-head screws through the br

– 8 –Control Panel FeaturesONOFFDELAYHOURSCYCLESELECT1 - 24 HR.LOW RINSE AIDHEAVYNORMALLIGHTGLASSESAIR-DRY SPEED RINSECLEANON/OFF With door open, pres

– 9 –DELAY HOUR This option allows you to delay the start of a wash cycle for up to 24 hours.SELECTIONWith the door open, turn the dishwasher ON by pr