Monogram ZBD6890 Manual do Utilizador

PUB # 31-9116 03/04MODEL SERIES:TECHNICAL SERVICE GUIDETop Control Monogram DishwashersZBD6800KZBD6880KZBD6890KGE Consumer & Industrial

– 10 –Middle Spray ArmCheck the holes in the spray arm for bits of china, seeds, and other foreign matter. Also, check the spray arm for rotation.Remo

– 11 –Fill FunnelThe top section of the fi ll funnel separates from the main body. The fi ll funnel body is held in place by a nut (located on the insid

– 12 –Circulation Pump and MotorThe dishwasher must be removed from its in stal la tion to gain access to the circulation pump and motor. The circulat

– 13 –Heating ElementThe heating element can be activated using Service Mode.The dual-wattage heating element produces 875 watts during wash, to help

– 14 –Note: When replacing the turbidity sensor, always run the Factory Test Mode to calibrate the turbidity sensor to the control board.When installi

– 15 –Note: To prevent leaks after installation, ensure that hose-to-valve connection is good and that clamp is in place.Water Valve and Flood SwitchT

– 16 –Water Valve Test1. Attempt to activate water valve using Service Mode. Pump out water as necessary using Service Mode. If an in ter mit tent fa

– 17 –Membrane KeypadThe door panel must be removed to access the membrane keypad (see Door Panel).• When removing the membrane keypad, peel the keyp

– 18 –Control ModuleThe door panel must be removed to access the control module (see Door Panel). The main control is considered a “smart” control, ca

– 19 –Detergent/Rinse ModuleThe door panel must be removed to access the detergent/rinse module (see Door Panel).The detergent rinse module is held in

– 2 –IMPORTANT SAFETY NOTICE The information in this service guide is intended for use byindividuals possessing adequate backgrounds of electrical

– 20 –Active Vent The active vent consists of the fan, motor, housing, and vent louver motor.The active vent helps to reduce the noise level and heat

– 21 –Service ModeNote: Service mode may be used for 30 minutes maximum. After 30 minutes, the service mode will automatically turn off.Note: 3-digit

– 22 –Always run the factory test mode to calibrate when replacing the turbidity sensor, control module board, and membrane keypanel.The factory test

– 23 –TroubleshootingNote: Carefully remove the keypad label. When replacing the keypad label, make sure the lights and pads align properly with the m

– 24 –Strip Circuits1234GYNXSXOXNTCTURBIDITY SENSORBXBWBWNO COMJ2-9J2-8DOORINTERLOCKWATER VALVEDOOR INTERLOCKJ2-2PXFLOODSWITCHWATER VALVEWX725-1200CNO

– 25 –WARNING: Disconnect electrical power before servicing.Caution: Label all wires prior to disconnection. Wiring errors can cause improper and dan

– 26 –WarrantyYOUR MONOGRAM DISHWASHER WARRANTY Proof of original purchase date is needed to ob

– 3 –Active Vent ...20Circulation

– 4 –Model DesignatorDesignates features – the higher the number, the more features.The letter des ig nat ing the year re peats every 12 years.Example

– 5 –Control Features1. Wash Cycles Use the arrow pads to scroll through the wash cycles. The light above or next tothe selected pad will be ON to ind

– 6 –GLASSES Heavy 10.0 gal., 45 min.(on some models) Medium 7.2 gal., 33 min.Light 7.2 gal., 32 min.This cycle is specifically designed for glasses.P

– 7 –7. Status Indicator Lights (indicators vary by model)The Status display tells you what is happening while the dishwasher is in operation and may

– 8 –Component Locator ViewsDoor View (Front Panel Removed)Inside Cabinet View1 - Upper Spray Arm2 - Middle Spray Arm 3 - Main Conduit4 - Hub (low

– 9 –Fill FunnelBottom ViewLeft Side ViewFront of Dish wash erRear of Dish wash erWater ValveFill HoseDrain Tube AssemblyDrain Line Check ValveJunctio