Monogram ZTD910 Manual do Utilizador descarregar pdf

ADVANCE PLANNING

• Refer to “Installation Preparation” for

information on appropriate placement and

necessary clearances when planning

installation.

• Avoid placing cabinetry directly above cooktop

when possible.

• If cabinetry is used above cooking surface:

– Use cabinets no more than 13″ deep.

– Maintain 30″ minimum clearance between

cooktop and unprotected cabinets directly

above cooktop.

– If clearance is less than 30″, protect cabinet

bottoms with flame-retardant millboard at

least 1/4″ thick, or gypsum board at least

3/16″ thick, covered with 28 gauge sheet

steel or .02″ thick copper.

– Clearance between cooktop and protected

cabinetry must not be less than 24″.

– An exhaust hood that projects at least 5″

beyond front of cabinets can reduce risk

of burns caused by reaching over heated

surface units.

– Working areas adjacent to the cooktop

should have 18″ minimum clearance between

countertop and cabinet bottom.

•A 36″ or wider exhaust hood with 350 CFM or

greater airflow rating is recommended for use

over this Monogram cooktop.

• Installation must conform with local codes.

In the absence of local codes, the gas cooktop

must comply with the National Fuel Gas Code,

ANSI Z223.1, latest edition.

• Gas supply should be located near the opening

for this cooktop (see Preparing the Opening and

Gas Connection sections of this manual). The

supply should provide natural gas at 7″ of water

column pressure (11″ of water column for LP

gas) and a maximum of 14″ of water column

for natural or LP gas.

• The electric spark ignition feature for this

model requires a 120V electrical power supply

be located in the immediate vicinity of this

cooktop (see Electrical Connections section

of this manual).

WB28T10185 High Altitude Kit

For operation above 5,000 feet, order

WB28T10185 Conversion Kit. This kit includes

orifices for both LP and Natural gas operation.

Installation Preparation

INSTALLATION OPTIONS

Cooktop and ZVB36 Downdraft Vent Combination

Installation

These cooktops may be installed with a 36″

Monogram Downdraft Vent, model ZVB36.

See page 12 for cutout and clearances.

– The countertop must have a deep flat surface to

accommodate the combined installation of the

cooktop and vent.

– The downdraft vent with blower, motor and

ductwork will occupy the base cabinet.

– Consideration must be given to electrical and gas

supply locations. See page 8.

– Read the Downdraft Vent Installation Instructions

packed with the product, or to review ahead of

time, order Pub. No. 49-80185.

Cooktop and ZTD910 or ZKD910 Warming Drawer

Combination Installation

These cooktops may be installed over a Monogram

30″ or 27″ Warming Drawer, model ZTD910 or

ZKD910. See page 13 for cutout and clearances.

– Consideration must be given to electrical and gas

supply locations. See page 8.

– Read the Warming Drawer Installation

Instructions packed with the product, or to review

ahead of time, order Pub. No. 49-8937.

Cooktop and ZET1 or ZET938 Single Oven

Combination Installation

These cooktops may be installed over a Monogram

30″ Oven, model ZET1 or ZET938. See page 14 for

cutout and clearances.

– Consideration must be given to electrical and gas

supply locations. See page 8.

– Read the 30″ Oven Installation Instructions

packed with the product, or to review ahead of

time, order Pub. No. 31-10633.

Installation Above Cabinet Drawers

• When installing the cooktop above a base

cabinet with drawers, it may be necessary to

use a shorter depth (front to back) drawer to

allow clearance for the gas connection.

1 2 3 4 5 6 7

Resumo do Conteúdo

Página 1 - Installation Preparation

ADVANCE PLANNING • Refer to “Installation Preparation” forinformation on appropriate placement andnecessary clearances when planninginstallation.• Avo

Página 2

DIMENSIONS AND CLEARANCES1. Overall cooktop dimensions:2. Use a 36″ or wider base cabinet.• Cut the opening in the countertop. To ensureaccuracy, it i

Página 3

POWER SUPPLY LOCATIONSGas supply:These cooktops are shipped from the factory set for either natural gas or LP gas. Check to be sure you have the corre

Página 4 - Installation Instructions

Installation Instructions9INSTALL THE COOKTOPA. Remove the screws on the sides of the cooktopburner box. Use those screws to attach the sidemounting b

Página 5 - Installation Options

COOKTOP INSTALLATION WITH A 36″ MONOGRAM DOWNDRAFT VENT,MODEL ZVB36The installation of the downdraft vent with this cooktop requires careful considera

Página 6

Installation Options13COOKTOP INSTALLATION OVER A MONOGRAM WARMING DRAWER,MODEL ZTD910 OR ZKD910These cooktops may be installed over a 30″or 27″ Warmi

Página 7

COOKTOP INSTALLATION OVER A 30″ MONOGRAM SINGLE OVEN,MODEL ZET1 OR ZET938These cooktops may be installed over theMonogram ZET1 or ZET938 single oven.