Monogram ZDP364ND Manual do Proprietário

InstallationInstructions31-1068904-08 JR30", 36" and 48"Professional RangesCuisinières professionnelles de 30’’ (76 cm) 36" (91 cm

Installation Preparation4-WIRE POWER CORD INSTALLATIONNOTE: A 4-wire cord is connected to the range at the factory. Use the following steps to changea

REMOVE PACKAGING•Cut the metal banding. Lift the carton straight up.•Locate the two runner strips from the top of the packaging. These strips will be

RunnersTo SupportLeveling LegsPanelRangeOpeningRange OpeningRunners for Rolling the Range into Position2 Lift the toekick out of the foam base.Inst

INSTALL ANTI-TIP DEVICESTEP 3Installation13Anti-Tip Parts Provided• Attach the Anti-Tip Brace onto the bottom of the range in the recessed area. Insta

IMPORTANT: Disconnect the range and theindividual shut-off valve from the gas supply pipingsystem during any pressure testing of that systemat test pr

15REPLACE OVEN DOOR(S)Skip this step if oven doors are in place.IMPORTANT:Do not lift the door by the handle.To replace the oven doors:•Firmly grasp t

InstallationCHECK BURNERSCheck to be sure that burner heads and caps are securely seated. •Check for proper ignition:– Push in one control knob and tu

17InstallationACCESSORIES—TOEKICK (provided)•Install the toekick after the range has been leveled.•Measure the distance between the floor and the bott

ZX12B30PSS, ZX12B36PSS, ZX12B48PSS Accessory InstallationOPTIONAL ACCESSORIES—12" HIGH BACKSPLASHTOOLS AND MATERIALS REQUIRED•Gloves to protect a

TOOLS AND MATERIALS REQUIRED• Gloves to protect against sharp edges• T-15 and #2 Phillips screwdrivers• Drill with 3/32" and 9/64" bits•Safe

2Installation InstructionsBEFORE YOU BEGINRead these instructions completely and carefully.•IMPORTANT— Save these instructions forlocal inspector’s us

INSTALL COVER PANELS (cont.)ALTERNATE METHOD: When side access is blocked• Install bottom cover over the bottom support whiledriving one screw into ea

TOOLS YOU NEEDED FOR CONVERSIONCONVERT THE REGULATORDisconnect all electrical power at the main circuitbreaker or fuse box.A. Remove the rear venttrim

CHANGE GRILL ORIFICE(if present)Locate the 1–1/2” long Grill orifice. Select for your gas type. LP—.047, NAT—.067A. Remove the grill cover,grates and

CHANGE GRIDDLE ORIFICE(if present)Locate the 3/4” long Griddle orifice.Select for your gas type. LP—.047, NAT—.076A. Lift off the griddle fluecover. R

Printed in MexicoNOTA: Mientras efectúa las instalaciones descriptas en estelibro, deben utilizarse gafas o lentes de seguridad.Para servicio técnico

30" to 36" Adjustable HeightBacksplash With ShelfZXADJB48PSS, for 48" wide rangesZXADJB36PSS, for 36" wide rangesZXADJB30PSS, for

4Design InformationPRODUCT DIMENSIONS AND CLEARANCES48" Range ModelsToekick/legHeight3-1/4” to 4-3/4”1”35-1/4”to 36-3/4”Height47-7/8” Width28-1/4

PRODUCT DIMENSIONS AND CLEARANCES36" Range ModelsDesign Information53-1/4” to 4-3/4”1”35-1/4”to 36-3/4”Height35-7/8” Width28-1/4”18”Min.13” Max.3

6Design InformationPRODUCT DIMENSIONS AND CLEARANCES30" Wide Range Models18”Min.13” Max.3-1/4” to 4-3/4”1”35-1/4”to 36-3/4”Height30” Min.ADDITION

PRODUCT DIMENSIONS AND CLEARANCESDesign Information48", 36" and 30" Range Models712" Min. to combustibles or 0" to a non-comb

8Installation InformationMATERIALS REQUIRED (not provided)Shut Off ValvePipe Fittings5-foot maximum length, 5/8" O.D. CSA-approved flexiblemetal

POWER SUPPLY LOCATIONSGas Supply: •The natural gas models are designed to operateat 5" water column pressure. For proper operation,the pressure o